Nikon 1 V1 Software and Firmware Download

Nikon 1 V1 Software and Firmware Download
Nikon 1 V1 Software and Firmware Download

Nikon has released new firmware for its Nikon 1 J1 and V1 digital cameras, with 1.40 as the version number. These cameras have a CMOS image sensor in the CX format of Nikon on board and can be equipped with different lenses. For more information about the Nikon 1 series and these two models, we refer to our hands-on from October 2011. The list of changes in this update is as follows:

Changes in this version

  • Support for the FULL / LIMIT focus limit switch on the 1 NIKKOR VR 70-300 mm f / 4.5-5.6 has been added.
  • If the camera firmware is updated to this version, autofocus will not work if an FT1 with L firmware version 1.10 or earlier is used.
  • Users of the FT1 must update the L firmware of the FT1 to version 1.20, along with the update of the camera firmware.
  • The problem that caused photos to not be printed with some printers via the PictBridge standard has been resolved.

Keep your digital system camera up to date. The firmware update for the "Nikon 1 V1" offered here for download brings the system camera up to date.

A firmware update can bring several advantages: First, the manufacturer thus improves errors that affect the function of the camera. Second, new features can be added through a firmware update. Third, the processing speed of the camera may benefit from the firmware update.

These improvements are offered by the 1.30 update

  • The update also makes continuous auto-focus mode AF-C possible using the bayonet adapter FT1 with AF-S lenses. However, the bayonet adapter must also be updated to firmware version 1.10.
  • The Nikon 1 Nikkor 32mm 1: 1.2 is now supported.
  • Regarding the magnification of images taken in MF (manual focus) mode, the following changes have been made. The simple magnification has been added, and the period before restoration of the normal display has been shortened for inactivity after a partial magnification.
  • When shooting in the shooting mode "Electronic (Hi)" at 10 fps and the FT1 bayonet adapter attached, the shutter speed that was displayed when the shutter-release button was pressed halfway and the shutter speed displayed when the shutter-release button is pressed halfway were different. This issue has been resolved.
  • The accuracy of the time synchronization with the GP-N100 GPS receiver attached to the camera and set the option "Set clock via GPS" to "Yes" has been improved. Nikon states that timing synchronization errors cannot be completely ruled out by GPS.
These improvements are offered by the update 1.21
  • After attaching a lens, the view sometimes appeared on the camera monitor or in the electronic viewfinder immediately after the camera was turned on. This issue has been resolved.
These improvements are offered by the update 1.12
  • If you recorded slow-motion movies with a frame rate of 1200 / s, it could happen that single pictures were taken twice. The update fixes this problem.
These improvements are available in Update 1.11
  • Incorrect overexposure due to the external flash SB-N5 has been reduced
  • The update also fixes a possible malfunction of the camera, which occurred when switching between the live view display and the electronic viewfinder under manual focus (MF) with simultaneous enlargement.
These improvements are offered by the update 1.10
  • The bayonet adapter FT1 is now supported. The adapter allows the use of NIKKOR Nikon F bayonet lenses with the system camera. Autofocus is available when using AF-S lenses. The focus mode must be set to AF-S (Single AF) and the AF area selector to Single field, with only the centre focus area can be used. The image stabilizer works when using appropriate lenses.
  • The "Pixel Mapping" option has been added to the system menu. Use this feature when a shot has unexpected light spots.

Note: The firmware update is at your own risk. If the update process is interrupted, the camera may be damaged. If you do not trust the update process, contact a photo retailer.

This is how the firmware update works

  • Download the update and unzip the file.
  • Make sure the camera battery is fully charged.
  • Insert a blank SD-HC card into the camera and format the card. This feature can be found in the camera menu. After that switch off the camera, remove the SD-HC card.
  • Insert the SD-HC card into the card reader of your computer. Copy the firmware file to the SD-HC card. Put the file in the main directory of the memory card, do not create folders. Finally, remove the SD-HC card using the Safely Remove Hardware feature. or? eject ??.
  • Insert the SD-HC card into the camera and then turn on the camera. In the Camera menu, locate the firmware update subpage. Confirm the update to the new version.
  • Switch off the camera after the update and after a few seconds again. Check the firmware version in the camera menu. Has the new version been installed?

Conclusion: To keep your Nikon 1 V1 up-to-date and to ensure optimal performance of the device, update the firmware of the camera regularly. Larger software updates may even include new features for your camera.

Link Download Nikon 1 V1 Firmware for Windows Operating System:
Download Firmware

Link Download Nikon 1 V1 Firmware for Macintosh Operating System:
Download Firmware

Link Download Nikon 1 J1 Firmware for Windows Operating System:
Download Firmware

Link Download Nikon 1 J1 Firmware for Windows Operating System:
Download Firmware

0 Response to "Nikon 1 V1 Software and Firmware Download"

Post a Comment

Disclaimer: Images, articles or videos that exist on the web sometimes come from various sources of other media. Copyright is fully owned by the source.

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel